Parts

Showing1-60 of 347 items
12V 5-Amp-Hour Switch Mode Charger for Hydraulic Lift Trailers

12V 5-Amp-Hour Switch Mode Charger for Hydraulic Lift Trailers

Price: $55

Bright Way Accessories and Parts - 3805211 Trailer Breakaway Kit Battery Charger Bright Way Switch mode charger is designed to charge any hydraulic trailer drawing power off of Group 24 batteries. The unique design of the charger does not supply power after the battery is fully charged, which increases the longevity of the battery. Features:- Switch mode charger designed for use with hydraulic dump or lift trailers Charger does not supply amp power when the battery that it is connected to is fully charged, increasing the life of the battery Switch does not heat up because it is not transformer based

Stock #: 3805211
Air Lift Load Controller II Compressor System for Air Helper Springs - Single Path

Air Lift Load Controller II Compressor System for Air Helper Springs - Single Path

Price: $268

Air Lift Air Suspension Compressor Kit - AL25592 Air Lift Wired Control Single Path Analog Display The Load Controller II system automatically kicks in if it senses that your air spring pressure is too low. In-cab, single-path controls let you adjust 1 pair of air springs. Perfect for light-to-medium-duty applications and occasional hauling. Features:- Restores air spring pressure automatically when it is too low Detects when air pressure in your helper springs falls below minimum level Minimum pressure level is typically set at 5 psi, but you can manually adjust system to sense when air pressure is below 10 psi Keeps air pressure above minimum level to ensure long spring life Lets you monitor and adjust 1 pair of air springs with a single-path, in-cab controller and gauge Maintains equal air pressure in both springs for front-to-back leveling Boasts quiet, high-volume airflow for virtually vibration-free operation Performs well for light-duty or medium-duty applications and for occasional hauling or towing Works with any brand of air springs Includes wiring harness for fast, easy installation Specs:- Compressor duty cycle: 4 minutes on, 5 minutes off 60-Day money-back guarantee 2-Year limited warranty Low air pressure is the chief reason for air spring failure. To avoid this, you have to either regularly monitor your air springs or find a device that will do it for you. Air Lift's Load Controller II air control system for light-to-medium-duty vehicles does just that. If the air pressure in your air springs falls below the minimum level, the system's low-pressure sensor detects the decrease in air pressure. Then the system activates automatically to adjust air pressure as needed. Load Controller II has virtually vibration-free operation and is made to help support your air springs as they take on weighty loads. The single-path controller lets you adjust one pair of air springs, so you can maintain equal air pressure in both springs for simple front-to-back leveling. A gauge provides detailed monitoring of your air pressure. Air Lift kits are designed to keep your vehicle at normal ride height. You can find the normal ride height of your vehicle by unloading it and measuring the distance between the bottom edge of your wheel well and the center of the hub. After you find and record this distance, you can regulate the amount of air that you send to your air springs to maintain normal ride height - even when you are hauling a heavy load. You will need to adjust the air pressure in your air bags according to the size of your load.

Stock #: AL25592
etrailer Ball Mount Kit - 3/4" Rise or 2" Drop - 7500 lbs

etrailer Ball Mount Kit - 3/4" Rise or 2" Drop - 7500 lbs

Price: $52

Features:- Works with 2" x 2" trailer hitch receivers (Class III) Kit includes: (2) Ball mounts with 3/4" rise / 2" drop (# 2923) Capacity: 7,500 lbs GTW and 750 lbs TW (1) 1-7/8" x 1" x 2-1/8" trailer hitch ball (# 19260) Capacity: 2,000 lbs GTW (1) 2" x 1" x 2-1/8" Trailer hitch ball (# 63845) Capacity: 7,500 lbs GTW (1) Pin and clip (# PC3) (1) etrailer Ball Mount Bag (# ETBMB) 989899 etrailer Ball Mount Kit - 7,500 lbs

Stock #: 989899
Ball Mount - 4-3/4" Rise 6" Drop - 10-1/4" Long - 6000 lbs

Ball Mount - 4-3/4" Rise 6" Drop - 10-1/4" Long - 6000 lbs

Price: $31

Features:- Ball mount lets you hook up your trailer to your tow vehicle Shank slides into your vehicle's hitch receiver Ball platform provides mounting point for hitch ball (sold separately) Sturdy steel construction with hollow shank Both drop and rise positions available to ensure level towing Hitch pin and clip or hitch lock sold separately Specs:- Application: 2" x 2" trailer hitch receiver Gross towing weight: 6,000 lbs Tongue weight: 600 lbs Length: 10-1/4" from center of hitch pin hole to center of ball hole Rise: 4-3/4" from top of inside of hitch opening Drop: 6" from top of inside of hitch opening Ball hole diameter: 1"

Stock #: 40346
Ball Mount for 2" Hitches - 3/4" Rise 2" Drop - 8-1/2" Long - 7.5K

Ball Mount for 2" Hitches - 3/4" Rise 2" Drop - 8-1/2" Long - 7.5K

Price: $20

Features:- Ball mount lets you hook up your trailer to your tow vehicle Shank slides into your vehicle's hitch receiver Ball platform provides mounting point for hitch ball (sold separately) Angle-cut end on shank allows for easy installation and removal Both drop and rise positions available to ensure level towing Sturdy steel construction with a hollow shank Black powder coat finish covers a-coat base for superior rust protection Pin and clip included Specs:- Application: 2" x 2" trailer hitch receivers Gross towing weight: 7,500 lbs Tongue weight: 750 lbs Length: 8-1/2" from center of hitch pin hole to center of ball hole 2-1/2" From center of hitch pin hole to back end of ball mount Rise: 3/4" from top of inside of hitch opening Drop: 2" from top of inside of hitch opening Ball hole diameter: 1" Pin hole diameter: 5/8"

Stock #: 2923
Trailer Hitch Receiver Lock - Flush Design for 2" Trailer Hitches

Trailer Hitch Receiver Lock - Flush Design for 2" Trailer Hitches

Price: $25

Features:- Trailer hitch receiver lock with flush locking design - Fits 2" x 2" trailer hitches (class III and class IV) - Pin diameter: 5/8" - Inside width: 2-5/8" - Overall length: 6" - Covered key slot prevents corrosion - Double-chrome plated for maximum rust resistance - Patented, pick-proof, screw-and-lock security - All weather grips for improved handling in extreme environments

Stock #: e98880
LED Trailer Fender Light for Trailers Over 80" Wide

LED Trailer Fender Light for Trailers Over 80" Wide

Price: $11

3-15/16" x 1-1/4". Waterproof LED marker light can be installed on your trailer fender. Amber light faces front, and red light faces rear. Surface mount with bracket (not included). Accepts standard 1-prong or 2-prong plug. P2 rated. Features:- Dual-face LED trailer light installs on your trailer fender Thinline Series has a low profile so that light can fit in tight spaces Sonically sealed, waterproof housing and lens unit is submersible LEDs make great replacements for incandescent lights Last 50 times longer More efficient - provide brighter light with less power output No bulbs to replace - no brittle filaments Durable polycarbonate housing and lens Red and amber lens over white LEDs Compatible with 12V DC systems Surface mount on trailer with bracket (A65B - sold separately) Accepts industry standard 1-prong or 2-prong plug P2 rated Specs:- Quantity: 1 fender light Dimensions: 3-15/16" long x 1-1/4" tall x 7/8" thick Distance between mounting holes (center on center): 3" Diodes: 10 Power draw at 12.8V: 0.048 amps

Stock #: MCL65ARB
LED Trailer Fender Light w/ Bracket

LED Trailer Fender Light w/ Bracket

Price: $12

3-15/16" x 1-1/4". Waterproof LED marker light can be installed on your trailer fender. Amber light faces front, and red light faces rear. Surface mount to trailer with bracket. Hardwired with 1-prong plug. P2 rated. Features:- Dual-face LED trailer light installs on your trailer fender Thinline Series has a low profile so that light can fit in tight spaces Sonically sealed, waterproof housing and lens unit is submersible LEDs make great replacements for incandescent lights Last 50 times longer More efficient - provide brighter light with less power output No bulbs to replace - no brittle filaments Durable polycarbonate housing and lens Red and amber lens over white LEDs Compatible with 12V DC systems Surface mount on trailer with included bracket Hardwired with industry standard 1-prong plug P2 rated Specs:- Quantity: 1 fender light Dimensions with bracket: 4-1/16" long x 1-1/4" tall x 1-1/8" thick Light dimensions: 3-15/16" long x 1-1/4" tall x 7/8" thick Distance between mounting holes (center on center): 3" Diodes: 10 Power draw at 12.8V: 0.048 amps

Stock #: MCL67ARB
Double Eye Tandem Hanger Kit 2 1/2" Tall

Double Eye Tandem Hanger Kit 2 1/2" Tall

Price: $92

• Fits 1-3/4" wide double eye springs • Includes everything needed to attach a double eye suspension on a tandem axle trailer The kit includes: 2ea 2 1/2" tall front hangers 2ea 2 1/2" tall rear hangers 2ea 5 7/16" tall center hangers 2ea straight equalizers (A2251B) 8ea 2 5/8" shackle straps 12ea 3" x 9/16" shackle/spring eye bolts 12ea 9/16" locknuts 2ea 3 1/2" x 3/4" equalizer bolts with grease zerks 2ea 3/4" castle nuts 2ea cotter pins

Stock #: APT1
Slipper Style Single Axle Hanger Kit 3 3/4" Tall

Slipper Style Single Axle Hanger Kit 3 3/4" Tall

Price: $45

• Fits 2" wide slipper springs • Includes everything needed to attach a slipper spring suspension on a single axle trailer The kit includes: 2ea 3 3/4" Tall front hangers 2ea 5 1/6" Tall rear hangers 4ea 3 1/2" x 9/16" spring eye bolts 4ea 9/16" locknuts

Stock #: APS6SE
Slipper Style Tandem Alxe Hanger Kit

Slipper Style Tandem Alxe Hanger Kit

Price: $118

• Fits 2" wide slipper springs • Includes everything needed to attach a slipper spring suspension to a tandem axle trailer The kit includes: 2ea 721584 front hangers 2ea 721585 rear hangers 2ea 721586 center hangers 2ea E4541 equalizers 2ea 7845B 7/8" equalizer bolts 2ea 78CN 7/8" castle nuts 2ea 165649 cotter pins 8ea 91635B 9/16" x 3-1/2" spring eye bolts 8ea 916DLN 9/16" locknuts

Stock #: APT6SE
Digital Calipers

Digital Calipers

Price: $25

• Measures outside, inside, step, and depth with precision • Features stainless steel construction with a large easy-to-read display • 0-6in SAE and 0-150mm metric range • Thumb wheel lock and fine engraved markings • Includes a battery and a heavy-duty plastic case to keep the calipers safe and clean

Stock #: W80152
3K Sidewind Pipe Mount Swivel Jack 15in Lift

3K Sidewind Pipe Mount Swivel Jack 15in Lift

Price: $44

For welding to frame of the trailer, the following jack comes with a mounting bracket for weld-on applications. Jack is ideal for uses with ag, industrial, commercial, recreational, and many other types of trailers. • Includes pin and lanyard assembly • pressed in grease zerk for easy greasing of the jack • Weld-on • Sidewind • Sand foot attached • 15" Lift • Black primer • 3,000 Static Capacity • 2,000lb Lifting Capacity

Stock #: TJP2002SB
5K Sidewind Pipe Mount Swivel Jack 15in Lift

5K Sidewind Pipe Mount Swivel Jack 15in Lift

Price: $100

Bulldog round jacks are recognized as the industry standard by leading agricultural, commercial, horse, livestock, and other trailer manufacturers. For more than three quarters of a century, Bulldog jacks have been demonstrated to be the most reliable, field-proven jacks on the market. • 5,000lb Lifting capacity • 15" Lift • 2" Tube diameter • 5 13/16" Handle radius • 5/8" Pin • Limited 5-year warranty (A) Retracted=15.4" (B) Extended=30.4 (C) Clearance=6.4"

Stock #: 178203
1 7/8in 2in & 2 5/16in Triple Ball Mount

1 7/8in 2in & 2 5/16in Triple Ball Mount

Price: $69

Features three welded trailer balls on a solid shank Allows for quick switching between trailer ball sizes Mounts on trailer hitches with a 2" x 2" receiver tube opening Fits 1 7/8", 2" or 2 5/16" couplers and accepts up to 10,000 lbs. GTW (depending on the ball) Permanently attached trailer balls cannot be loosened or stolen Shank constructed from solid steel for optimum strength Protected by a durable powder coat finish GTW/TW Ball 1: 5,000 LB/500 LB GTW/TW Ball 2: 7,500 LB/750 LB GTW/TW Ball 3: 10,000 LB/1,000 LB Length: 7 IN and 8 1/2 IN Shank Type: Solid Receiver Tube Size: 2 IN Finish: Black Powder Coat

Stock #: 45650
Tow & Stow 2 5/16 & 2in Balls 5in Drop

Tow & Stow 2 5/16 & 2in Balls 5in Drop

Price: $224

The B&W Tow & Stow is easily installed and adjustable. You can switch between 2 different ball sizes and is adjustable up to a 5" drop. When the hitch is not in use, it will stow under the vehicle. • Has 2-5/16" & 2" balls • 5" drop • 10k capacity • Pins into the receiver for easy installation • Corrosion resistant black powder coat finish

Stock #: TS10037B
Universal Cam Style Door Latch

Universal Cam Style Door Latch

Price: $37

Universal Cam Style Door Latch 5654X This plain finish steel cam-lock is for all van bodies, trucks, and trailers. It can be used with side or rear door applications. The lock can be installed on flush to 3/4" offset doors. A bridge type keeper prevents accidental opening and ensures safe locking action. The positive double action handle gives dual protection against jarring in transit. • Uses a 3/4" ID pipe NOT INCLUDED • Replacement parts are available • Handle welds to pipe Measurements: 1/8" Thick pipe retainer straps 1-3/4" Maximum lock protection 1/2" Square padlock or seal eye 1-7/8" Width of keeper 13/32" Diameter of mounting holes Handle is 13-3/4" Long

Stock #: 5654X
4in Round Clear LED 10 Diode Utility Light

4in Round Clear LED 10 Diode Utility Light

Price: $26

Optronics 4" Round Clear LED Sealed Utility Light Sealed, flush mount, clear LED utility light. 10 super diodes for bright, dependable performance. Features sonically sealed, waterproof lens and housing in a single unit. All-weather molded plastic housing and durable lens protect against corrosion. Accepts industry standard 2-prong plug for easy retrofit of incandescent lights. Requires mounting grommet and plug for complete installation. Not certified for backup light function. • Clear lens • 10 Diodes • 4 5/16" Diameter • 1 15/16" Tall • Light only

Stock #: BUL-43CB
LH Fender Mount Red/Amber Clearance/Marker Light

LH Fender Mount Red/Amber Clearance/Marker Light

Price: $5

• Surface mount • Mounts on 3" centers • Lens with reflex eliminates need for separate reflector • Driver's side • Two-wire design includes both lead and ground wire • Snap-on lens, replaceable bulb • Female plug on power wire, grounding eyelet on ground wire • Uses MC-44AB, MC-44RB incandescent replacement lights • Uses MCL-44AB, MCL-44RB LED replacement lights

Stock #: BA-44FNL
RH Fender Mount Red/Amber Clearance/Marker Light

RH Fender Mount Red/Amber Clearance/Marker Light

Price: $5

Optronics RH Fender Mount Red/Amber Clearance/Marker Light • Surface mount • Mounts on 3" centers • Lens with reflex eliminates need for separate reflector • Passenger's side • Two-wire design includes both lead and ground wire • Snap-on lens, replaceable bulb • Female plug on power wire, grounding eyelet on ground wire • Uses MC-44AB, MC-44RB incandescent replacement lights • Uses MCL-44AB, MCL-44RB LED replacement lights

Stock #: BA-44FNR
2-5/16in 14K Stamped A-Frame Coupler

2-5/16in 14K Stamped A-Frame Coupler

Price: $33

Ram Stamped 2 5/16" A-Frame Coupler 14,000lb Capacity Heavy-duty A-frame coupler features steel construction, with an oily finish and an easy-to-use latch. Stamped couplers are 100% ball fitted to ensure a proper fit when coupler is hooked up to a hitch ball. Coupler latches are set up for easy coupling and uncoupling. Stamped couplers include all SAE required markings and are compliant to standard J684. • 50 º A-frame trailer • For 2-5/16" hitch ball • 14,000lb Capacity • Weld-on

Stock #: CA5400
Ramp Spring Right Hand 2K (lbf-in) Torque For 1 1/2

Ramp Spring Right Hand 2K (lbf-in) Torque For 1 1/2

Price: $14

Right Hand 2K (lbf-in) torque ramp spring for trailer ramps This high quality ramp spring helps to raise the ramp and save your back. • Accepts 1.5" rod or pipe • OD is 2.5" • Each leg is 4" long from the coil to tip • 11" overall length • Right Hand • The right hand spring is marked with green

Stock #: RS16933RH
Gooseneck Hitch Kit

Gooseneck Hitch Kit

Price: $484

• Fits 1973-1987 Chevrolet & GMC 1/2, 3/4 & 1 Ton Trucks (Requires Drilling). Complete B&W gooseneck hitch kit(rails, center section, & hardware included). Solid, machined 2 5/16" ball. Durable powder-coat finish. Only a 4" hole is needed in the bed. Bolts to existing holes in the frame with no drilling or welding. • Hardware included • Turnover ball(square shank) • Drilling or welding required • 30k capacity • Limited lifetime Warranty

Stock #: BW1400R
Companion Slider 5th Wheel Hitch Kit

Companion Slider 5th Wheel Hitch Kit

Price: $1,640

We know what it's like to tow with a short bed truck! That's why we designed our slider hitch to give you twelve inches of slide, so you can have the extra room to maneuver your fifth-wheel. And it's a Companion so you'll love the ride. It's removable! Free up your truck bed when you are not towing. The Companion Slider utilizes the B&W Turnoverball under-bed mounting system. • Gross towing weight: 18,000lbs • Vertical load limit: 4,500lbs • Limited 5-year warranty • 12" of movement, for turning and maneuvering clearance in shortbed trucks. • Automatically latches in both directions- only get out of the truck once to move into maneuvering position. • Tight tolerances in sliding mechanism, moves smoothly without the rattle. • Three vertical adjustments, 17", 18", 19". • Fully articulating coupler head allows front to back and side to side pivoting. • 1" thick, wrap-around jaws fit kingpin perfectly, eliminating sloppy starts and stops. • Polyurethane bushings provide a quiet, rattle free towing experience. • Utilizes the B&W Turnoverball under-bed mounting system. Pull a Gooseneck or a 5th Wheel with the same system. • Can be removed (two people!) for a clean bed with no rails. No mounting rails means using your truck for more than towing. • Footprint: 34.75" Wide x 45" Deep • Measurement from center of hitch post to front edge (cab-side) of hitch: 15" • Gooseneck hitch sold separately

Stock #: BW3405
Companion 5th Wheel Hitch Kit Ford

Companion 5th Wheel Hitch Kit Ford

Price: $1,055

• Fits 2011 and newer Ford Super Duty trucks with factory-installed towing prep package. Customers surprised with the Ford prep package from the factory now have a choice in fifth wheel hitches. The Companion OEM, designed to fit the new Ford OEM hitch platform, installs and removes easily with its' two-piece design. It's notable for its effortless hookup and release with the cam-actuated latching mechanism. 1" thick cast locking jaws are machined with tight tolerances, providing a perfect connection to the camper and a smooth towing experience. • Fits 2011 and newer Ford Super Duty trucks with factory-installed towing prep package • Gross towing weight: 20,000lbs • Vertical load limit: 5,000lbs • Limited 5-year warranty • No mounting rails means it's removable and you can use your truck for more than towing. • Fully articulating head allows front to back and side to side pivoting. • Three vertical adjustments from 16.75" to 18.75" • 2" of front to back adjustment with three coupler positions • Cam action latching handle for easy release, even when parked on unlevel sites • 1" thick, wrap-around jaws fit kingpin perfectly, eliminating sloppy starts and stops. • Polyurethane bushings provide a quiet, rattle free towing experience • Fits 4 pucks in truck bed. Release handles and it easily converts to a level bed. • Distance between puck holes: 30" Wide x 13" Deep • Footprint: 33.5" Wide x 16.5" Deep

Stock #: BW3300
Companion 5th Wheel Hitch for Flatbeds

Companion 5th Wheel Hitch for Flatbeds

Price: $930

The same coupler used on the Companion is used with the Companion(tm) Flatbed, but with a short base. It's designed to be used with steel flatbeds. The Companion Flatbed is rated at 22,000lbs and is able to sit in a 20"x20" well, up to 4" deep. The Companion Flatbed utilizes the B&W Turnoverball under-bed mounting system, which means you can easily remove the Companion Flatbed RV Hitch and use your truck for other things. Free up your truck bed when you are not towing. • 22K Capacity • Cam action latching handle for easy release, even when parked on unlevel sites • Utilizes the B&W Turnoverball(tm) under-bed mounting system. Pull a Gooseneck or a 5th Wheel with the same system. • No mounting rails means using your truck for more than towing. • 1" thick, wrap-around jaws fit kingpin perfectly, eliminating sloppy starts and stops. • Polyurethane bushings provide a quiet, rattle free towing experience. • Product Weight: Base 50 lbs, Coupler 75 lbs • Footprint 17.25" Wide x 18" Deep

Stock #: BW3050R
Gooseneck Hitch Kit

Gooseneck Hitch Kit

Price: $484

• Fits 2002-2008 Dodge 1/2 Ton Long and Short Bed (Except Mega-Cab). Complete B&W gooseneck hitch kit(rails, center section, & hardware included). Solid, machined 2 5/16" ball. Durable powder-coat finish. Only a 4" hole is needed in the bed. Bolts to existing holes in the frame with no drilling or welding. • Hardware included • Turnover ball(square shank) • No drilling or welding required • 30k capacity • Limited lifetime Warranty

Stock #: BW1316R
Gooseneck Hitch Kit

Gooseneck Hitch Kit

Price: $484

• Fits 2009-2018 Dodge 1/2 Ton Trucks All Beds • 2013-18 Dodge 1/2 Ton Trucks All Beds Except Trucks with Four-Corner Air Suspension System (Only 4685 and RVK3500 with special post work with this hitch). • The Companion slider will not work with this hitch Complete B&W gooseneck hitch kit(rails, center section, & hardware included). Solid, machined 2 5/16" ball. Durable powder-coat finish. Only a 4" hole is needed in the bed. Bolts to existing holes in the frame with no drilling or welding. • Hardware included • Turnover ball(square shank) • No drilling or welding required • 30k capacity • Limited lifetime Warranty

Stock #: BW1309R
Gooseneck Hitch Kit

Gooseneck Hitch Kit

Price: $484

• Fits 2004-2014 Ford 1/2 Ton Trucks All Beds. Complete B&W gooseneck hitch kit(rails, center section, & hardware included). Solid, machined 2 5/16" ball. Durable powder-coat finish. Only a 4" hole is needed in the bed. Bolts to existing holes in the frame with no drilling or welding. • Hardware included • Turnover ball(square shank) • No drilling or welding required • 30k capacity • Limited lifetime Warranty

Stock #: BW1104R
Gooseneck Hitch Kit

Gooseneck Hitch Kit

Price: $484

• Fits 1997-2003 Ford 1/2 & LIGHT DUTY 3/4 Ton Trucks, & 2004 Heritage Edition. Complete B&W gooseneck hitch kit(rails, center section, & hardware included). Solid, machined 2 5/16" ball. Durable powder-coat finish. Only a 4" hole is needed in the bed. Bolts to existing holes in the frame with no drilling or welding. • Hardware included • Turnover ball(square shank) • No drilling or welding required • 30k capacity • Limited lifetime Warranty

Stock #: BW1197R
Gooseneck Hitch Kit

Gooseneck Hitch Kit

Price: $484

• Fits 1980-1996 Ford 1/2 Ton Trucks All Beds. Complete B&W gooseneck hitch kit(rails, center section, & hardware included). Solid, machined 2 5/16" ball. Durable powder-coat finish. Only a 4" hole is needed in the bed. Bolts to existing holes in the frame with no drilling or welding. • Hardware included • Turnover ball(square shank) • No drilling or welding required • 30k capacity • Limited lifetime Warranty

Stock #: BW1150R
Gooseneck Hitch Kit

Gooseneck Hitch Kit

Price: $484

• Fits 1980-1998 Ford 3/4 & 1 Ton WITH Overload Springs (requires Drilling 2 Holes). Complete B&W gooseneck hitch kit(rails, center section, & hardware included). Solid, machined 2 5/16" ball. Durable powder-coat finish. Only a 4" hole is needed in the bed. Bolts to existing holes in the frame with or welding. • Hardware included • Turnover ball(square shank) • No welding required • 30k capacity • Limited lifetime Warranty

Stock #: BW1110R
Gooseneck Hitch Kit

Gooseneck Hitch Kit

Price: $484

• Fits 1980-1998 Ford 3/4 & 1 Ton WITHOUT Overload Springs. Complete B&W gooseneck hitch kit(rails, center section, & hardware included). Solid, machined 2 5/16" ball. Durable powder-coat finish. Only a 4" hole is needed in the bed. Bolts to existing holes in the frame with no drilling or welding. • Hardware included • Turnover ball(square shank) • No drilling or welding required • 30k capacity • Limited lifetime Warranty

Stock #: BW1100R
Gooseneck Hitch Kit

Gooseneck Hitch Kit

Price: $484

• Fits 2001-2007 Chevrolet & GMC 1 Ton Truck (With 2 bed cross members over the axle). Complete B&W gooseneck hitch kit(rails, center section, & hardware included). Solid, machined 2 5/16" ball. Durable powder-coat finish. Only a 4" hole is needed in the bed. Bolts to existing holes in the frame with no drilling or welding. • Hardware included • Turnover ball(square shank) • No drilling or welding required • 30k capacity • Limited lifetime Warranty

Stock #: BW1062R
Gooseneck Hitch Kit

Gooseneck Hitch Kit

Price: $484

• Fits 1988-1998 Chevrolet & GMC 1/2, 3/4, & 1 Ton Short Bed Trucks • 1999-2000 Chevrolet & GMC 3/4 & 1 Ton Short Bed Trucks (Full C-Channel Frame). Complete B&W gooseneck hitch kit(rails, center section, & hardware included). Solid, machined 2 5/16" ball. Durable powder-coat finish. Only a 4" hole is needed in the bed. Bolts to existing holes in the frame with no drilling or welding. • Hardware included • Turnover ball(square shank) • No drilling or welding required • 30k capacity • Limited lifetime Warranty

Stock #: BW1050R
Gooseneck Hitch Kit

Gooseneck Hitch Kit

Price: $484

• Fits 1988-1998 Chevrolet & GMC 1/2, 3/4, & 1 Ton Long Bed Trucks 1999-2000 Chevrolet & GMC 3/4 & 1 Ton Heavy Duty Long Bed Trucks (Full C-Channel Frame). Complete B&W gooseneck hitch kit(rails, center section, & hardware included). Solid, machined 2 5/16" ball. Durable powder-coat finish. Only a 4" hole is needed in the bed. Bolts to existing holes in the frame with no drilling or welding. • Hardware included • Turnover ball(square shank) • No drilling or welding required • 30k capacity • Limited lifetime Warranty

Stock #: BW1000R
Gooseneck Hitch Kit

Gooseneck Hitch Kit

Price: $484

• Fits 2007-2018 Chevrolet & GMC 1/2 Ton Long Bed Only New Boxed Frame. Complete B&W gooseneck hitch kit(rails, center section, & hardware included). Solid, machined 2 5/16" ball. Durable powder-coat finish. Only a 4" hole is needed in the bed. Bolts to existing holes in the frame with no drilling or welding. • Hardware included • Turnover ball(square shank) • No drilling or welding required • 30k capacity • Limited lifetime Warranty

Stock #: BW1007R
Gooseneck Hi-rise Repl Ball

Gooseneck Hi-rise Repl Ball

Price: $133

This solid, machined hitch ball is a hi-rise replacement for the 2-5/16" ball that came standard with your B&W(no rise) • Replacement hi-rise ball for B&W gooseneck hitch • 20k capacity • 1" rise • Solid machined steel • square shank

Stock #: BW2050
5th Wheel Rail Spacer Kit

5th Wheel Rail Spacer Kit

Price: $17

• Fits 2000-2006 Toyota Tundra The spacers in this kit are designed to ensure proper spacing between your truck's frame and bed, despite the deep corrugations in your pickup's bed. Requires B&W universal base rail installation kit (RVR3200 - sold separately). • Eases installation of 5th-wheel mounting kit • Spacers provide the required 1/2" spacing between the frame and truck bed, preventing damage to the bed when you torque the bolts • Works with B&W universal, 10-bolt base rail kit (RVR3200 - sold separately) • Fits 2000-2006 Toyota Tundra • Includes 8 spacers • Made in the USA

Stock #: RVR3206
5th Wheel Rail Bracket Kit

5th Wheel Rail Bracket Kit

Price: $99

Semi-custom brackets make it faster and easier to install your fifth-wheel trailer hitch. B&W universal, 10-bolt base rail kit (RVR3200) sold separately. » Fits 09-12 Dodge Ram 1500 including Crewcab (Used with the Patriot 5th wheel hitch) • Semi-custom brackets mount beneath your truck bed to provide attachment points for 5th - wheel rails • Works with B&W universal, 10-bolt base rail kit (RVR3200 - sold separately) • Sturdy steel construction • Corrosion-resistant powder coat finish • Hardware included • Made in the USA »» ACTUAL PRODUCT NOT SHOWN

Stock #: RVR3205
5th Wheel Rail Spacer Kit

5th Wheel Rail Spacer Kit

Price: $48

• Fits 2007-2012 Toyota Tundra The spacers in this kit are designed to ensure proper spacing between your truck's frame and bed, despite the deep corrugations in your pickup's bed. Requires B&W universal base rail installation kit (RVR3200 - sold separately). • Eases installation of 5th-wheel mounting kit • Spacers provide the required 1/2" spacing between the frame and truck bed, preventing damage to the bed when you torque the bolts • Works with B&W universal, 10-bolt base rail kit (RVR3200 - sold separately) • Fits 2007-2012 Toyota Tundra • Includes (2) 1/2" block spacers, (2) 1" long tube spacers, and necessary hardware • Made in the USA

Stock #: RVR3204
5th Wheel Patriot Rail Bracket Kit

5th Wheel Patriot Rail Bracket Kit

Price: $115

Semi-custom brackets make it faster and easier to install your fifth-wheel trailer hitch. B&W universal, 10-bolt base rail kit (RVR3200) sold separately. » Fits 04-12 Nissan Titan (Used with the Patriot 5th wheel hitch) • Semi-custom brackets mount beneath your truck bed to provide attachment points for 5th-wheel rails • Works with B&W universal, 10-bolt base rail kit (RVR3200 - sold separately) • Sturdy steel construction • Corrosion-resistant powder coat finish • Hardware included • Made in the USA »» ACTUAL PRODUCT NOT SHOWN

Stock #: RVR3203
Showing1-60 of 347 items

Get a Quote

Please enter your contact information and one of our representatives will get back to you with more information.